Here is My HowTo for Samsung Instinct Wap

[midiology]

I had already written this in another thread, after seeing how many folks were wanting the cricket web to work on their samsung instinct, but there were so many who said it wouldnt work...
So I decided to put My How To in its own thread to get better exposure...




You will need Cricket PRL ,CDMA Workshop and QPST and the samsung modem drivers for this...
Please search,, they are easy to find...

Install Cdma workshop, and Qpst if you havent already...
Now install the modem drivers for your instinct,,,

Remove your memory card if you have one in the phone.. and plug your phone in to your computer...
after driver installation right click on mycomputer, go to properties,, go to device manager,,, look under com ports,, double click on samsung com port to bring its properties up and find out the com port number and remember it..

now go into cdma workshop and select the comport that the phone is on,, click connect,, then once connected click QCDM for Qualcomm DM Mode,,, after a few seconds your phone info should pop up on the left side,,,

go to security tab,, click read spc,, your six digit spc should pop up,,, click send spc,, it should say phone unlocked,,, now replace numbers with six zeros,, then click write spc,, once done then go to other tab,,
under prl click write prl,, search for your cricket prl and pow it should say written..

once done move on to the next steps...


After Changing your spc to 000000
and flashing the Cricket prl to the phone...
do the esn change through cricket..
perform *228 and get all things updated...

after this go back to Qpst and read the phone..
once you read the phone.. go to m.ip and change from mobile ip to simple ip only,,, and look at the first 2 user profiles under m.ip open each one up and change the Nai to 10DigitNumber@mycricket.com,, for both standard and tethered...
remove any ip address that you find in these 2 profiles. and remove any other profiles except the first 2.
also make sure both of them say enabled...,,

now go to ppp config...
look at the tabs that say um and an... under these 2 tabs,, the user id should be 10DigitNumber@Mycricket.com tethered id should be the same,, password is cricket in lowercase on both tabs,, remove any dns ip address you find in either tab also. just make sure all ip address are blank.

once you are completed with this,, move on to the next step..

click on phone icon
click on dialer..
enter ##3282#
click user name
click edit
enter your spc which should already be 000000 by now
starting from the top here ya go...

User Name "10DigitNumber@mycricket.com"
SPI MN-HA "1234"
SPI MN-AAA "1234"
M Home Address "066.179.166.148"
Prim Ha Ip "010.000.005.021"
Sec Ha Ip "010.000.005.022"
Rev Tunneling "Off"
AAA Password "cricket"
HA Password "cricket"

click done,, allow the phone to reboot...

Now do ##3282# again.. this time go to browser
click edit
enter spc
youll see gateway1 and gateway2,,, under both of these
you will see primary and secondary,,, set primary and secondary ip`s for both gateways to 172.029.223.007,, they will all be the same ip address,, and set the Port and secure Port for all gatways to 8080,, hit done reboot and padow.. there you go...

I have tried to make this as clear As I can,, If you have any issues,, start all over... and start from the top...

Also this should work on quite a few other Sprint phones,,
This is what I do for a living at the wireless company I work for,, and so far it has worked on Samsung upstage, Instinct,, Sanyo katana, and many others,,,

Any questions just let me know...

And to all those Who have Pda/Smart PHones come visit us over at PPCGeeks.com



If your browser is stuck in Vision Account provisioning due to the phone being new unactivated before,, or from a hard reset,,, see my other post down below to reopen the browser again.. http://www.cricketphonetalk.com/foru....html#post5721

[InSaNeCaiN]

does the phone have to have been previously activated with sprint? I can't get around the "profile update"

[midiology]

does the phone have to have been previously activated with sprint? I can't get around the "profile update"

I replied to your pm,, but I will put some info here for everyone..

The broswer on this phone has a registration system,,
in order for the browser to even come up it checks that it has been registered with sprint...

so if it has not ever been activated then everytime you try to bring up the browser it will get stuck saying that it is trying to check your account...

if this happens let me know I can try to walk you through what I did,, it is quite a process,, but I can try to help..

I had gotten cricket wap to work on my phone,,, but then I accidentally reset my phone in the TestMode,,, and lost everything I had done... even though I put all the settings back in,, the browser was still trying to activate my sprint account that I didnt have..

I played around and finally got it to come back up again.. and bam i am back up and running,, and on evdo this thing is snappy...

no tabbed browsing, and no way to upload through email though,,, try to send a gmail or something,, and click the attachment button to send a pic or something it just pops up with warning.. and thats it...

but for viewing web pages,, it is very snappy and finger friendly....

[juice01]

I replied to your pm,, but I will put some info here for everyone..

The broswer on this phone has a registration system,,
in order for the browser to even come up it checks that it has been registered with sprint...

so if it has not ever been activated then everytime you try to bring up the browser it will get stuck saying that it is trying to check your account...

if this happens let me know I can try to walk you through what I did,, it is quite a process,, but I can try to help..

I had gotten cricket wap to work on my phone,,, but then I accidentally reset my phone in the TestMode,,, and lost everything I had done... even though I put all the settings back in,, the browser was still trying to activate my sprint account that I didnt have..

I played around and finally got it to come back up again.. and bam i am back up and running,, and on evdo this thing is snappy...

no tabbed browsing, and no way to upload through email though,,, try to send a gmail or something,, and click the attachment button to send a pic or something it just pops up with warning.. and thats it...

but for viewing web pages,, it is very snappy and finger friendly....

i am getting the same thing and my phone is new. Would it be to much to ask for you to post how you got past that?

[midiology]

i am getting the same thing and my phone is new. Would it be to much to ask for you to post how you got past that?

Ok to all the folks that have a new phone or have hard reset the phone,, these settings will absolutely not get your browser past the provisioning state,, if your browser is trying to set up vision services and hangs,, it is because of this.. ill try to explain..

You see I reset the phone when I got it.. like a moron.. and after resetting it I never could get the browser to come up again,, it kept trying to update my account...
so here is what the deal is,, and how I think I got it back...

your browser doesnt know if you have your ppp settings installed or not..
it basically uses a policy,,

when the phone is new,, or reset,, when you open the browser it opens up a hidden NAI application in the background to provision your Sprint vision account,,, once the vision is updated,, it writes to the browser policy telling it it is complete,, then the browser will boot on its own without checking your vision data service... but this will not work on cricket since it is not on sprints vision service...
Sooooooooo... if this is your case... then following the steps Ive provided,,, start from the beginning,, but this time start clean,, go into qpst and clear all account info and ip address`s from M.IP and PPP config... then start from the very beginning and add it all back in,,,

then when completed , go to phone,, do the ##brew# enter spc
then youll see a bunch of little icons,, tap each one once while looking at the bottom of the screen,,, look until you see something that just says browser,, double click on this icon,, it may try to bring up your browser,, once you do this, back out and go back to brew and look for the icon that says sde_app there are a couple that say sde,, but use the one that says SDE_APP,, double tap on this it should bring up a list of like Start sde:addr start sde:mailto etc..
click on start sde:http and then I think you click browse,, the browser may or may not come up when you click this,, but i did this and after exiting brew it no longer tried to verify account,, it just brought the browser up properly like it should,, I dont know if it was a coincidence or what but it got it back..

[juice01]

Ok to all the folks that have a new phone or have hard reset the phone,, these settings will absolutely not get your browser past the provisioning state,, if your browser is trying to set up vision services and hangs,, it is because of this.. ill try to explain..

You see I reset the phone when I got it.. like a moron.. and after resetting it I never could get the browser to come up again,, it kept trying to update my account...
so here is what the deal is,, and how I think I got it back...

your browser doesnt know if you have your ppp settings installed or not..
it basically uses a policy,,

when the phone is new,, or reset,, when you open the browser it opens up a hidden NAI application in the background to provision your Sprint vision account,,, once the vision is updated,, it writes to the browser policy telling it it is complete,, then the browser will boot on its own without checking your vision data service... but this will not work on cricket since it is not on sprints vision service...
Sooooooooo... if this is your case... then following the steps Ive provided,,, start from the beginning,, but this time start clean,, go into qpst and clear all account info and ip address`s from M.IP and PPP config... then start from the very beginning and add it all back in,,,

then when completed , go to phone,, do the ##brew# enter spc
then youll see a bunch of little icons,, tap each one once while looking at the bottom of the screen,,, look until you see something that just says browser,, double click on this icon,, it may try to bring up your browser,, once you do this, back out and go back to brew and look for the icon that says sde_app there are a couple that say sde,, but use the one that says SDE_APP,, double tap on this it should bring up a list of like Start sde:addr start sde:mailto etc..
click on start sde:http and then I think you click browse,, the browser may or may not come up when you click this,, but i did this and after exiting brew it no longer tried to verify account,, it just brought the browser up properly like it should,, I dont know if it was a coincidence or what but it got it back..

Your a lifesaver. It worked. I got the browser back by only going thru your first step. Double clicked on the browser icon and got back out. Thanks again

[juice01]

Ok to all the folks that have a new phone or have hard reset the phone,, these settings will absolutely not get your browser past the provisioning state,, if your browser is trying to set up vision services and hangs,, it is because of this.. ill try to explain..

You see I reset the phone when I got it.. like a moron.. and after resetting it I never could get the browser to come up again,, it kept trying to update my account...
so here is what the deal is,, and how I think I got it back...

your browser doesnt know if you have your ppp settings installed or not..
it basically uses a policy,,

when the phone is new,, or reset,, when you open the browser it opens up a hidden NAI application in the background to provision your Sprint vision account,,, once the vision is updated,, it writes to the browser policy telling it it is complete,, then the browser will boot on its own without checking your vision data service... but this will not work on cricket since it is not on sprints vision service...
Sooooooooo... if this is your case... then following the steps Ive provided,,, start from the beginning,, but this time start clean,, go into qpst and clear all account info and ip address`s from M.IP and PPP config... then start from the very beginning and add it all back in,,,

then when completed , go to phone,, do the ##brew# enter spc
then youll see a bunch of little icons,, tap each one once while looking at the bottom of the screen,,, look until you see something that just says browser,, double click on this icon,, it may try to bring up your browser,, once you do this, back out and go back to brew and look for the icon that says sde_app there are a couple that say sde,, but use the one that says SDE_APP,, double tap on this it should bring up a list of like Start sde:addr start sde:mailto etc..
click on start sde:http and then I think you click browse,, the browser may or may not come up when you click this,, but i did this and after exiting brew it no longer tried to verify account,, it just brought the browser up properly like it should,, I dont know if it was a coincidence or what but it got it back..

I know this is a Cricket forum but would you be able to help me with the same Instinct but i want it on Pocket Service. My email is sky0167@msn.com Let me know. thanks ahead of time.

[midiology]

I know this is a Cricket forum but would you be able to help me with the same Instinct but i want it on Pocket Service. My email is sky0167@msn.com Let me know. thanks ahead of time.

Im sorry,, but Im not familliar with Pockets Ip Address sets,, only alltel and cricket,,,

[midiology]

Your a lifesaver. It worked. I got the browser back by only going thru your first step. Double clicked on the browser icon and got back out. Thanks again

Great,, Im glad it worked for ya...

[InSaNeCaiN]

i still get "preparing data services"